3D Inspection & Mesh Editing

609 topics in this forum

1. Koordinaten von Zylindern anzeigen

   By [St...] , August 19, 2021
   • 7 replies
   • 1.3k views
   • 
   • [Ch...]
   • May 3, 2023

2. Error in 3D Calibration from image series

   By [mo...] , April 29, 2023
   • 1 reply
   • 448 views
   • 
   • [Na...]
   • May 2, 2023

3. Rename a check, e.g. “T” instead of “dN”

   By [Je...] , April 23, 2023
   • 1 reply
   • 535 views
   • 
   • [Je...]
   • April 25, 2023

4. Measuring GD&T to Datum System that is not fully constrained.

   By [le...] , April 18, 2023
   • 1 reply
   • 583 views
   • 
   • [Ch...]
   • April 19, 2023

5. Measuring Angle Between 2 Planes

   By [Jo...] , April 6, 2023
   • 1 reply
   • 957 views
   • 
   • [Ti...]
   • April 18, 2023

6. Position prüfen (mit CZ)

   By [Ch...] , March 30, 2023
   • 4 replies
   • 1.6k views
   • 
   • [Ch...]
   • April 12, 2023

7. hard to catch points when right angle has radius

   By [Th...] , April 5, 2023
   • 3 replies
   • 602 views
   • 
   • [Di...]
   • April 11, 2023

8. Which association criterion is used by GOM to find a datum line for a cylinder which covers less than 180°?

   By [Er...] , April 3, 2023
   • 3 replies
   • 573 views
   • 
   • [Ch...]
   • April 4, 2023

9. Automatically Recalculate doesn't work

   By [Ma...] , March 31, 2023
   • 5 replies
   • 629 views
   • 
   • [Be...]
   • April 3, 2023

10. how to meaure negative angle

    By [Ad...] , March 29, 2023
    • 2 replies
    • 1.6k views
    • 
    • [Ad...]
    • March 31, 2023

11. Measuring thickness of a clear part

    By [Jo...] , March 30, 2023
    • 1 reply
    • 544 views
    • 
    • [Ja...]
    • March 30, 2023

12. Spalt zwischen zwei Teilen visualisieren

    By [Jö...] , March 22, 2023
    • 3 replies
    • 639 views
    • 
    • [Jö...]
    • March 28, 2023

13. Angle of a cone "units"

    By [Kl...] , March 8, 2023
    • 1 reply
    • 3.7k views
    • 
    • [Je...]
    • March 20, 2023

14. MMC on Composite Tolerances

    By [Ry...] , March 1, 2023
    • 6 replies
    • 1.2k views
    • 
    • [Ti...]
    • March 18, 2023

15. export quality of inspection sections

    By [Fa...] , March 15, 2023
    • 2 replies
    • 546 views
    • 
    • [Je...]
    • March 16, 2023

16. Creating Offset Planes

    By [Ja...] , March 15, 2023
    • 2 replies
    • 1k views
    • 
    • [Na...]
    • March 16, 2023

17. Inclined tolerance zone - request for opinion

    By [Ma...] , March 15, 2023
    • 0 replies
    • 471 views
    • 
    • [Ma...]
    • March 15, 2023

18. Area not included in surface comparison

    By [Wo...] , February 27, 2023
    • 2 replies
    • 625 views
    • 
    • [No...]
    • March 10, 2023

19. (Help Needed) Decrease only on side of the borders when you calculate surface

    By [Vi...] , March 9, 2023
    • 1 reply
    • 446 views
    • 
    • [Na...]
    • March 9, 2023

20. Dynamic Profile Tolerance Modifier

    By [Ad...] , March 3, 2023
    • 2 replies
    • 530 views
    • 
    • [Ch...]
    • March 6, 2023

21. Angle of a cone

    By [Ti...] , February 26, 2023
    • 4 replies
    • 2.4k views
    • 
    • [Ti...]
    • March 4, 2023

22. Schnittkreis in einem Rohrbogen Messen

    By [Th...] , February 17, 2023
    • 1 reply
    • 522 views
    • 
    • [Na...]
    • March 3, 2023

23. Auxiliary CAD Lines CALYPSO vs GOM

    By [Vi...] , February 28, 2023
    • 2 replies
    • 537 views
    • 
    • [Vi...]
    • March 1, 2023

24. Darstellung Schnittkurve und Linien / Representation of section curve and lines

    By [An...] , February 22, 2023
    • 2 replies
    • 532 views
    • 
    • [An...]
    • February 25, 2023

25. Inspecting Point Clouds

    By [Ad...] , February 16, 2023
    • 4 replies
    • 1.1k views
    • 
    • [Ad...]
    • February 23, 2023